ARALDITE® CY 184 / ARADUR® HY 1238 / Accelerator DY 062 / Color Paste DW 9134

• Very high mechanical and dielectrical end properties.
• Good thermal shock resistance.
• High resistance to erosion under UV-radiations.
• High tracking and arc resistance.
• The use of silanised silica flour insures stable dielectrical properties under outdoor humid conditions.

General instructions for preparing liquid resin systems:

• Long pot life is desirable in the processing of any ARALDITE® casting resin system. Mix all of the components together very thoroughly at room temperature or slightly above and under vacuum. Intensive wetting of the filler is extremely important. Proper mixing will result in:

1. Better flow properties and reduced tendency to shrinkage
2. Lower internal stresses and therefore improved mechanical properties on object
3. Improved partial discharge behaviour in high voltage applications.

• For the mixing of medium to high viscous Araldite® casting resin systems and for mixing at lower temperatures, we recommend special thin film degassing mixers that may produce additional self-heating of 10-15°C as a result of friction.
• For low viscous Araldite® casting resin systems, conventional anchor mixers are usually sufficient. In larger plants, two premixers are used to mix the individual components (ARALDITE and ARADUR®) with the respective quantities of fillers and additives under vacuum. Metering pumps then feed these premixes to the final mixer or a continuous mixer. The individual premixes can be stored at elevated temperature (about 60°C) for up to about 1 week, de-pending on formulation. Intermittent agitation during storage is advisable to prevent filler sedimentation.
• Mixing time can vary from 0.5 to 3 hours, depending on mixing temperature, quantity, mixing equipment and the particular application. The required vacuum is 0.5 to 8 mbar. The vapour pressure of the individual components should be taken into account. In the case of dielectrically highly stressed parts, we recommend checking the quality consistency and predrying of the filler. Their moisture content should be < 0.2%.

Outdoor electrical insulation material for medium and high voltage applications in humid conditions: apparatus components, pin/post insulators, bushings, etc.

The effective pot-life is about 1 day at temperature below 25°C. Conventional batch mixers should be cleaned once a week or at the end of work. For longer interruptions of work, the pipes of the mixing and metering installations have to be cooled and cleaned to prevent sedimentation and/or undesired viscosity increase. Interruptions over a weekend (approx. 48h) without cleaning are possible if the pipes are cooled at temperature below 18°C. In case to use mixtures with high reactivity, we recommend to clean daily with the flexibilizer DY 045.

Mould temperature
Conventional vacuum casting : 80 - 100°C
APG process : 130 - 150°C
Demoulding times (depending on mould temperature and casting volume)
Conventional vacuum casting : 2 - 4 h
APG process : 10 - 30 min
Cure conditions (minimal post cure)
Conventional vacuum casting : 4h at 80°C + 10h at 140°C
APG process : 16h at 140°C

For any outdoor application, we recommend the use of silanised silica flour. Adgain it is essential to achieve a thorough crosslinking. To determine whether crosslinking has been carried to completion and the final proper-ties are optimal, it is necessary to carry out relevant measurements on the actual object or to measure the glass transition temperature. Different gel and postcuring cycles in the manufacturing process could influence the crosslinking and the glass transition temperature respectively.

ARADUR® HY 1238 is sensitive to humidity, partly emptied containers should be closed tightly immediately after use. It is necessary to store this product in the sealed original container

The components have to be stored in tightly sealed and dry original containers according to the storage conditions on the product label. Under these conditions, the shelf life will correspond to the expiration date stated on the label. After this date, the product may be processed only following reanalysis. Partialy emptied containers should be closed tightly immediately after use.