Enhanced TDS
Identification & Functionality
- Chemical Family
- RTU Product Type
- Technologies
- Product Families
Features & Benefits
- Product Features
- Key Properties
Excellent Mechanical and electrical properties
Applications & Uses
- Product End Uses
- Markets
- Applications
- Application Information
Encapsulation or potting of low voltage and electronic components
Regulatory & Compliance
- Manufacturing Facility Standards
Technical Details & Test Data
- Cured Properties
Key Value Unit Test Method Test Condition Specific gravity 1.42 g/cm³ DIN 55990 -- Glass transition temperature 65-70 °C IEC 1006 2h at 80°C + 1h at 120°C
Thermal linear coefficient (20–50°C) 84 ppm/K DIN 53752 2h at 80°C + 1h at 120°C
Thermal linear coefficient (60°C) 90 ppm/K DIN 53752 2h at 80°C + 1h at 120°C
Thermal linear coefficient (80°C) 111 ppm/K DIN 53752 2h at 80°C + 1h at 120°C
Thermal linear coefficient (90°C) 123 ppm/K DIN 53752 2h at 80°C + 1h at 120°C
Shore D hardness 80 -- DIN 53505 2h at 80°C + 1h at 120°C
Dielectric strength 32 kV/mm IEC 60243 2h at 80°C + 1h at 120°C
Thermal conductivity 0.18 W/mK ISO 8894 2h at 80°C + 1h at 120°C
Dielectric loss factor (tan δ, 50Hz) 0.7 % IEC 60250 2h at 80°C + 1h at 120°C
Dielectric constant (εr, 50Hz) 3.3 --- IEC 60250 2h at 80°C + 1h at 120°C
Electrolytic corrosion A1 grade IEC 60426 2h at 80°C + 1h at 120°C
- Processing
Casting / Impregnating
Safety & Health
- First Aid
Contamination of the eyes by resin, hardener or casting mix should be treated immediately by flushing with clean, running water for 10 to 15 minutes. A doctor should then be consulted. Material smeared or splashed on the skin should be dabbed off, and the contaminated area then washed and treated with a cleansing cream (see above). A doctor should be consulted in the event of severe irritation or burns. Contaminated clothing should be changed immediately. Anyone taken ill after inhaling vapours should be moved out of doors immediately. In all cases of doubt call for medical assistance.
- Handling Precautions
Safety precautions at workplace:
protective clothing : yes
gloves : essential
arm protectors : recommended when skin contact likely
goggles/safety glasses : yes
respirator/dust mask : recommended
Skin protection
before starting work : Apply barrier cream to exposed skin
after washing : Apply barrier or nourishing cream
Cleansing of contaminated skin : Dab off with absorbent paper, wash with warm water and alkali-free soap, then dry with disposable towels. Do not use solvents
Clean shop requirements : Cover workbenches, etc. with light coloured paper. Use disposable beakers, etc.
Disposal of spillage : Soak up with sawdust or cotton waste and deposit in plastic-lined bin
Ventilation:
of workshop : Renew air 3 to 5 times an hour
of workplace : Exhaust fans. Operatives should avoid inhaling vapours.
Storage & Handling
- Storage Conditions
Store the components in a dry place at 18-25°C, in tightly sealed original containers. Under these conditions, the shelf life will correspond to the expiry date stated on the label. After this date, the product may be processed only after reanalysis. Partly emptied containers should be tightly closed immediately after use. For information on waste disposal and hazardous products of decomposition in the event of a fire, refer to the Material Safety Data Sheets (MSDS) for these particular products.
Other
- Processing & Application Methods
- Application Information
Value Units Test Method / Conditions Mix Ratio 0.0054 %(W) Accelerator : Resin Mix Ratio 0.65 %(W) Hardener : Resin