AGOMET® F 330 / HARDENER Lacquer 2

• Hardener can be applied to substrate and stored for up to 30 days
• Rapid cure after joining, 20 minute handling strength
• High shear strength and peel strength
• Bonds well to a wide range of metals and plastic materials
• Very good temperature resistance

Pretreatment

The strength and durability of a bonded joint are dependant on proper pretreatment of the surfaces to be bonded, however the methacrylate adhesives can be used effectively with little surface preparation. Ideally joint surfaces should be cleaned with a good degreasing agent such as acetone, iso-propanol or proprietary degreasing agent in order to remove all traces of oil, grease and dirt. Low grade alcohol, gasoline (petrol) or paint thinners should never be used. The strongest and most durable joints are obtained by either mechanically abrading or chemically etching (“pickling”) the degreased surfaces.

Application of Adhesive
Depending on the type of application, the hardener Lacquer 2 can be applied by spraying, brushing, roll-coating or dipping one or both surfaces to be bonded. The Lacquer 2 dries sufficiently in about 4 minutes to allow bonding, transporting or storage. Surfaces coated with hardener Lacquer 2 can be stored for several weeks without losing the hardener’s reactivity. Once the hardener Lacquer 2 has dried, the adhesive is applied to one of the two surfaces. Then the parts are joined immediately and fixed under contact pressure. Polymerisation starts as soon as the adhesive touches the hardener Lacquer 2. The bond can be carefully handled after the time indicated overleaf to reach to lap shear strength of 1 MPa.

A layer of adhesive 0.15 to 0.25 mm thick will normally impart the greatest lap shear strength to a joint, although joints of up to 0.8mm gap can be assembled. For joint gap widths up to 0.4 mm, application of hardener Lacquer 2 to just one surface is sufficient. To bridge wider joint gaps, hardener Lacquer 2 must be applied to both parts. Gaps wider than 0.8 mm should be avoided since the adhesive may not fully cure.

The joint components should be assembled and clamped as soon as the adhesive has been applied. An even contact pressure throughout the joint area will ensure optimum cure.If adhesive is applied to one surface and hardener Lacquer 2 to the other, this method of separate processing allows bonding operations practically independent of the pot life.

Mechanical Processing

Specialist firms have developed metering, spraying and spreading equipment that enables the bulk processing of adhesive. We will be pleased to advise customers on the choice of equipment for their particular needs.

Equipment Maintenance

All tools should be cleaned before adhesives residues have had time to cure. The removal of cured residues is a difficult and time-consuming operation. If solvents such as acetone are used for cleaning, operatives should take the appropriate precautions and, in addition, avoid skin and eye contact.

Times to minimum shear strength

Average lap shear strengths of typical metal-to-metal joints (ISO 4587) (typical average values)
Cured for 7 days at 23°C and tested at 23°C
Pretreatment - Sand blasting

Average lap shear strengths of typical plastic-to-plastic joints (ISO 4587) (typical average values)
Cured for 7 days at 23°C and tested at 23°C
Pretreatment - Lightly abrade and isopropanol degrease.      Note - failure modes are mainly substrate failure

Lap shear strength versus temperature (ISO 4587) (typical average values)
Cure: = 7 days at 23°C

Roller peel test (ISO 4578) at 23°C (typical average values)    :   7.2 N/mm
Glass Transition Temperature (Tg)                                            :    54°C (Cured 7 days at 23°C)
Tensile strength (ISO 527) (typical values)                                :    14 MPa
Elongation at break:                                                                   :    3.5%
Coefficient of thermal expansion (-30°C/+30°C)                        :    60 x 10⁻⁶/⁰K (Cured 7 days at 23°C)

Lap shear strength versus immersion in various media at 23°C (typical average values)
Substrate – gritblasted aluminium

Lap shear strength versus tropical weathering (ISO 4587) (typical average values)
(40°C/ 92% RH), on aluminium, Cure: 7 days at 23°C

Lap strength versus heat ageing (typical average values)
Cure: 7 days at 23°C

Thermal cycling
100 cycles of 6 hour duration from -30°C to 70°C: 33.7 N/mm2
Shear modulus (DIN 53345)
cured 7 days at 23°C

Our products are generally quite harmless to handle provided that certain precautions normally taken when handling chemicals are observed. The uncured materials must not, for instance, be allowed to come into contact with food- stuffs or food utensils, and measures should be taken to prevent the uncured materials from coming in contact with the skin, since people with particularly sensitive skin may be affected. The wearing of impervious rubber or plastic gloves will normally be necessary; likewise the use of eye protection. The skin should be thoroughly cleansed at the end of each working period by washing with soap and warm water. The use of solvents is to be avoided. Disposable paper - not cloth towels should be used to dry the skin. Adequate ventilation of the working area is recommended.

Agomet® F330 and Agomet® Hardener Lacquer 2 may be stored at respectively at 2 - 8°C and 2 - 18°C in sealed containers. 

Our products are generally quite harmless to handle provided that certain precautions normally taken when handling chemicals are observed. The uncured materials must not, for instance, be allowed to come into contact with food- stuffs or food utensils, and measures should be taken to prevent the uncured materials from coming in contact with the skin, since people with particularly sensitive skin may be affected. The wearing of impervious rubber or plastic gloves will normally be necessary; likewise the use of eye protection. The skin should be thoroughly cleansed at the end of each working period by washing with soap and warm water. The use of solvents is to be avoided. Disposable paper - not cloth towels should be used to dry the skin. Adequate ventilation of the working area is recommended.