Products

ARALDITE® CW 1305 / ARADUR® HY 1300 is an optimally filled casting system for processing and curing at room temperature or slightly higher temperatures.

ARALDITE® CW 2122-1 / ARADUR® HY 1227-1 is a flame-retardant epoxy system with excellent electrical and mechanical properties, ideal for filled casting applications.

ARALDITE® CW 30386 / ARADUR® HW 30387 is a high Tg pre-filled epoxy resin system for potting electrical motors and power electronics.

ARALDITE® CW 30388 / ARADUR® HW 30389 is a high Tg pre-filled epoxy resin system for potting electrical motors and power electronics with improved thermal conductivity.

ARALDITE® CW 5715 / ARADUR® HY 5716 is a high-temperature filled epoxy encapsulation system. ARALDITE® CW 5715 with ARADUR® HY 5716 is a filled, high-temperature encapsulation system whose toughened characteristics result in superior anti-crack propagation.

ARALDITE® CW 5801-1 / ARADUR® HY 5801 is a two-component, epoxy-based potting and encapsulating system. ARALDITE® CW 5801-1 / ARADUR® HY 5801 is a 100% solids (no solvent) two-component, epoxy-based potting and encapsulating system designed especially for applications requiring very low shrinkage and excellent dielectric characteristics. Although the system will gel at room ambient temperature, an additional short elevated temperature post-cure is recommended to achieve optimal properties. This product is recommended for the encapsulation of electrical and electronic components.

ARALDITE® CY 8763 / ARADUR® HY 8763 is a high-performance, two-component epoxy system designed for sealed lead acid storage batteries. This system offers excellent sulfuric acid resistance and superior adhesion properties.

ARALDITE® DBF / ARADUR® HY 842 is a low-viscosity, unfilled epoxy casting resin system, curing at room temperature. High filler addition possibility.

ARALDITE® F / ARADUR® HY 840-1 is a liquid, cold-warm-curing, low-viscous impregnating and casting resin system with moderate reactivity and high flexibility after cure.

ARALDITE® GY 191 / ARADUR® HY 177 / ARADUR® HY 226 / ARADUR® 943 / REN® HY 956 can be used with a variety of different hardeners, enabling its processing characteristics and final properties to be adjusted to meet a wide range of production conditions and applications, in particularly where good impregnation is required such as electrical encapsulation of small transformers, filters, capacitors etc. done without or slightly de-gassing needed.

ARATHANE® CW 5631 / ARATHANE® HY 5610 is a ready-to-use resin designed for industrial and parts and components applications, particularly for control units, electric motors, and LEDs. It is ideal for stator end uses. The resin offers excellent flow properties, good penetration, scratch resistance, high hardness, a good surface finish, and is non-abrasive, making it suitable for demanding industrial applications.

EPOCAST® 88103-A/B casting system is a two-component material that cures at a low temperature. It is formulated to yield a cured polymer with good mechanical, optical, and electrical properties. EPOCAST® 88103-A/B casting system is formulated specifically for the encapsulation of light-emitting diodes. The product is suitable for use in applications that require the environmental protection properties of an epoxy combined with high-efficiency visible light transmission. EPOCAST® 88103-A/B casting system is also widely used as an optical electronic packaging (encapsulant) material.

EX 6240 / EX 6241 HARDENER is a liquid, heat-curing, two-component epoxy casting system containing fillers. This system is fusible to make excellent crack-resistant parts that can be used for the manufacturing of electrical bushings or dry-type transformers. The resin system can be processed by automatic pressure gelation (APG) or conventional encapsulation, such as gravity casting under vacuum. It is used in Dry-type transformers, Electrical bushings, and Electrical encapsulation.

Thermal and vibration: Full density (FD), lightweight foam technology for the potting and fixation of cells mounted in EV batteries or as moldable encapsulants in battery modules or packs. This technology can be used via common polyurethane dispensing process or pre-fabricated.

Thermal and vibration: Low density (LD), lightweight foam technology for the potting and fixation of cells mounted in EV batteries or as moldable encapsulants in battery modules or packs. This technology can be used via common polyurethane dispensing process or pre-fabricated.